Add a server on Azure Stack HCI, version 23H2

Applies to: Azure Stack HCI, version 23H2

This article describes how to manage capacity by adding a server (often called scale-out) to your Azure Stack HCI cluster.

About add servers

You can easily scale the compute and storage at the same time on your Azure Stack HCI by adding servers to an existing cluster. Your Azure Stack HCI cluster supports a maximum of up to 16 servers.

Each new physical server that you add to your cluster must closely match the rest of the servers in terms of CPU type, memory, number of drives, and the type and size of the drives.

You can dynamically scale your Azure Stack HCI cluster from 1 to 16 servers. In response to the scaling, the orchestrator (also known as Lifecycle Manager) adjusts the drive resiliency, network configuration including the on-premises agents such as orchestrator agents, and Arc registration. The dynamic scaling may require the network architecture change from connected without a switch to connected via a network switch.

Add server workflow

The following flow diagram shows the overall process to add a server:

To add a server, follow these high-level steps:

1. Install the operating system, drivers, and firmware on the new cluster server that you plan to add. For more information, see Install OS.
2. Add the prepared server via the Add-server PowerShell cmdlet.
3. When adding a server to the cluster, the system validates that the new incoming server meets the CPU, memory, and storage (drives) requirements before it actually adds the server.
4. Once the server is added, cluster is also validated to ensure that it's functioning normally. Next, the storage pool is automatically rebalanced. Storage rebalance is a low priority task that doesn't impact actual workloads. The rebalance can run for multiple days depending on number of the servers and the storage used.

Supported scenarios

For adding a server, the following scale-out scenarios are supported:

When upgrading a cluster from two to three servers, the storage resiliency level is changed from a two-way mirror to a three-way mirror.

Resiliency settings

In this release, for add server operation, specific tasks aren't performed on the workload volumes created after the deployment.

For add server operation, the resiliency settings are updated for the required infrastructure volumes and the workload volumes created during the deployment. The settings remain unchanged for other workload volumes that you created after the deployment (since the intentional resiliency settings of these volumes aren't known and you may just want a 2-way mirror volume regardless of the cluster scale).

However, the default resiliency settings are updated at the storage pool level and so any new workload volumes that you created after the deployment will inherit the resiliency settings.

Hardware requirements

When adding a server, the system validates the hardware of the new, incoming server and ensures that the server meets the hardware requirements before it's added to the cluster.

Prerequisites

Before you add a server, you would need to complete the hardware and software prerequisites.

Hardware prerequisites

Make sure to complete the following prerequisites:

1. The first step is to acquire the new Azure Stack HCI hardware from your original OEM. Always refer to your OEM-provided documentation when adding new server hardware for use in your cluster.
2. Place the new physical server in the predetermined location, for example, a rack and cable it appropriately.
3. Enable and adjust physical switch ports as applicable in your network environment.

Software prerequisites

Make sure to complete the following prerequisites:

• AzureStackLCMUser is active in Active Directory. For more information, see Prepare the Active Directory.
• Signed in as AzureStackLCMUser or another user with equivalent permissions.
• Credentials for the AzureStackLCMUser haven't changed.

Add a server

This section describes how to add a server using PowerShell, monitor the status of the Add-Server operation and troubleshoot, if there are any issues.

Add a server using PowerShell

Make sure that you have reviewed and completed the prerequisites.

On the new server that you plan to add, follow these steps.

1. Install the operating system and required drivers on the new server that you plan to add. Follow the steps in Install the Azure Stack HCI, version 23H2 Operating System.

2. Register the server with Arc. Follow the steps in Register with Arc and set up permissions.

   Note

   You must use the same parameters as the existing nodes to register with Arc. For example: Resource Group name, Region, Subscription, and Tentant.

3. Assign the following permissions to the newly added server nodes:

   • Azure Stack HCI Device Management Role
   • Key Vault Secrets User For more information, see Assign permissions to the server.

On a server that already exists on your cluster, follow these steps:

1. Sign in with the domain user credentials that you provided during the deployment of the cluster.

2. (Optional) Before you add the server, make sure to get an updated authentication token. Run the following command:

   Update-AuthenticationToken 
   

3. Run the following command to add the new incoming server:

   $HostIpv4 = "<IPv 4 for the new server>"
   $Cred = Get-Credential 
   Add-Server -Name "< Name of the new server>" -HostIpv4 $HostIpv4 -LocalAdminCredential $Cred 
   

4. Make a note of the operation ID as output by the Add-Server command. You use this operation ID later to monitor the progress of the Add-Server operation.

Monitor operation progress

To monitor the progress of the add server operation, follow these steps:

1. Run the following cmdlet and provide the operation ID from the previous step.

   $ID = "<Operation ID>" 
   Start-MonitoringActionplanInstanceToComplete -actionPlanInstanceID $ID 
   

2. After the operation is complete, the background storage rebalancing job will continue to run. Wait for the storage rebalance job to complete. To verify the progress of this storage rebalancing job, use the following cmdlet:

   Get-VirtualDisk|Get-StorageJob
   

   If the storage rebalance job is complete, the cmdlet won't return an output.

The newly added server shows in the Azure portal in your Azure Stack HCI cluster list after several hours. To force the server to show up in Azure portal, run the following command:

Sync-AzureStackHCI

Recovery scenarios

Following recovery scenarios and the recommended mitigation steps are tabulated for adding a server:

Troubleshoot issues

If you experience failures or errors while adding a server, you can capture the output of the failures in a log file. On a server that already exists on your cluster, follow these steps:

• Sign in with the domain user credentials that you provided during the deployment of the cluster. Capture the issue in the log files.

  Get-ActionPlanInstance -ActionPlanInstanceID $ID|out-file log.txt
  

• To rerun the failed operation, use the following cmdlet:

  Add-Server -Rerun
  

Next steps

Learn more about how to Repair a server.